Hot rolled

SSAB Boron 22 is a steel for hardening and pressing. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life.

SSAB Boron 22 is available in a thickness range of 0.70-80.00 mm and widths up to 1800 mm in coils, slotted coils and CTL and 3300 mm in slab form. Length up to 16 meters in cut form.

The minimum bending radius of the hot-rolled strip is 2 times the thickness of the sheet. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products.

The minimum bending radius of SSAB Boron 22 hot-rolled thick sheet is 3 x sheet thickness up to 16 mm. For instructions on bending thicker plates, contact SSAB Technical Support.

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Cold-rolled coils and sheet products: according to EN 10131. Tighter tolerances available on request.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Hot-rolled sheet products: supplied with tolerances that meet 3/4 of EN 10029 as a default value.

Cold-rolled coils and sheet products: according to EN 10131. Tighter tolerances available on request.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled sheet: width tolerance -0/+4-10 mm depending on thickness. Length tolerance -0/+15-75 mm depending on the length.

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot-rolled sheet products: shape tolerances according to EN 10029.

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled sheet: maximum deviation from flatness 6 mm/m.

Hot-rolled strip and hot-rolled plate: according to EN 10163-2, class A, subclass 3.

Cold-rolled coils and sheets are delivered in an annealed state.

Hot-rolled coils and sheets are supplied in rolled or annealed condition by separate agreement.

Heavy slabs are ready for rental.

Cold-rolled products are produced with an oiled or dry surface.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

Heavy plates are available as rolled, shot blasted or shot blasted and primed.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.

SSAB Boron 24 is a hardening and pressing steel. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life.

SSAB Boron 24 is available in thicknesses ranging from 2.00-80.00mm and widths up to 1800mm in coils, slotted coils and CTL and 3300mm in slab form. Length up to 16 meters in cut form.

The minimum bending radius of the hot-rolled strip is 2 times the thickness of the sheet. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products.

The minimum bending radius of SSAB Boron 24 hot-rolled thick sheet is 4 x sheet thickness up to 16 mm. For instructions on bending thicker plates, contact SSAB Technical Support. 

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Hot-rolled sheet products: supplied with tolerances that meet 3/4 of EN 10029 as a default value.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled sheet: width tolerance -0/+4-10 mm depending on thickness. Length tolerance -0/+15-75 mm depending on the length.

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot-rolled sheet products: shape tolerances according to EN 10029.

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled sheet: maximum deviation from flatness 6 mm/m.

Hot-rolled strip and hot-rolled plate: according to EN 10163-2, class A, subclass 3.

Hot-rolled coils and sheets are supplied in rolled condition.

Heavy slabs are ready for rental.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

Heavy plates are available as rolled, shot blasted or shot blasted and primed.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.

SSAB Boron 27 is a steel for hardening and pressing. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life.

The minimum bending radius of the hot-rolled strip is 2 times the thickness of the sheet. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products.

The minimum bending radius of SSAB Boron 27 hot-rolled thick sheet is 4 x sheet thickness up to 16 mm. For instructions on bending thicker plates, contact SSAB Technical Support.

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Hot-rolled sheet products: supplied with tolerances that meet 3/4 of EN 10029 as a default value.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled sheet: width tolerance -0/+4-10 mm depending on thickness. Length tolerance -0/+15-75 mm depending on the length

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot-rolled sheet products: shape tolerances according to EN 10029.

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled sheet: maximum deviation from flatness 6 mm/m.

Hot-rolled strip and hot-rolled plate: according to EN 10163-2, class A, subclass 3.

Hot-rolled coils and sheets are supplied in rolled or annealed condition by separate agreement.

Heavy slabs are ready for rental.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

Heavy plates are available as rolled, shot blasted or shot blasted and primed.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.

SSAB Boron 27Cr is a steel for hardening and pressing. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life.

SSAB Boron 27Cr is available in thicknesses ranging from 1.00-15.00mm and widths up to 1800mm in coils, slotted coils and CTL. Length up to 16 meters in cut form.

For details on available thickness and width combinations, please contact SSAB.

The minimum bending radius of the hot-rolled strip is 2 times the thickness of the sheet. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products.

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Cold-rolled coils and sheet products: according to EN 10131. Tighter tolerances available on request.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Cold-rolled coils and sheet products: according to EN 10131. Tighter tolerances available on request.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled strip products: according to EN 10163-2, class A, subclass 3.

Cold-rolled coils and sheets are delivered in an annealed state.

Hot-rolled coils and sheets are supplied in rolled or annealed condition by separate agreement.

Cold-rolled products are produced with an oiled or dry surface.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.

SSAB Boron 30 is a hardening and pressing steel. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life.

SSAB Boron 30 is available in thicknesses ranging from 2.00-80.00mm and widths up to 1800mm in coils, slotted coils and CTL and 3300mm in slab form. Length up to 16 meters in cut form.

The minimum bending radius of the hot-rolled strip is 2 times the thickness of the sheet. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products.

The minimum bending radius of SSAB Boron 30 hot-rolled thick sheet is 5 times the thickness of the sheet up to 16 mm. For instructions on bending thicker plates, contact SSAB Technical Support.

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Hot-rolled sheet products: supplied with tolerances that meet 3/4 of EN 10029 as a default value.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled sheet: width tolerance -0/+4-10 mm depending on thickness. Length tolerance -0/+15-75 mm depending on the length.

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot-rolled sheet products: shape tolerances according to EN 10029

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled sheet: maximum deviation from flatness 6 mm/m.

Hot-rolled strip and hot-rolled plate: according to EN 10163-2, class A, subclass 3.

Hot-rolled coils and sheets are supplied in rolled or annealed condition by separate agreement.

Heavy slabs are ready for rental.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

Heavy plates are available as rolled, shot blasted or shot blasted and primed.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.

SSAB Boron 33 is a steel for hardening and pressing. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life.

SSAB Boron 33 is available in thicknesses ranging from 2.00-16.00mm and widths up to 1800mm in rolls, slotted rolls and CTL. Length up to 16 meters in cut form.

The minimum bending radius of the hot-rolled strip is 2 times the thickness of the sheet. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products.

For more information, contact SSAB Technical Support.

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled strip and hot-rolled plate: according to EN 10163-2, class A, subclass 3.

Hot-rolled coils and sheets are supplied in rolled or annealed condition by separate agreement.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.

SSAB Boron 33Cr is a hardening and pressing steel. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life.

SSAB Boron 33Cr is available in thicknesses ranging from 2.00-16.00mm and widths up to 1800mm in coils, slotted coils and CTL. Length up to 16 meters in cut form.

The minimum bending radius of SSAB Boron 33Cr hot-rolled strip is 2 x sheet thickness. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products. For more information, contact SSAB Technical Support.

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled strip and hot-rolled plate: according to EN 10163-2, class A, subclass 3.

Hot-rolled coils and sheets are supplied in rolled or annealed condition by separate agreement.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.

SSAB Boron 36 is a steel for hardening and pressing. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life

SSAB Boron 36 is available in thicknesses ranging from 2.00-15.00mm and widths up to 1800mm in rolls, slotted rolls and CTL. Length up to 16 meters in cut form.

The minimum bending radius of SSAB Boron 36 hot-rolled strip is 3 x sheet thickness. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products. For more information, contact SSAB Technical Support.

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled strip and hot-rolled plate: according to EN 10163-2, class A, subclass 3.

Hot-rolled coils and sheets are supplied in rolled or annealed condition by separate agreement.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.

SSAB Boron 38 is a steel for hardening and pressing. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life.

SSAB Boron 38 is available in thicknesses ranging from 1.00-15.00mm and widths up to 1800mm in coils, slotted coils and CTL. Length up to 16 meters in cut form.

For details on available thickness and width combinations, please contact SSAB.

The minimum bending radius of the hot-rolled strip is 2 times the thickness of the sheet. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products.

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Cold-rolled coils and sheet products: according to EN 10131. Tighter tolerances available on request.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Cold-rolled coils and sheet products: according to EN 10131. Tighter tolerances available on request.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled strip and hot-rolled plate: according to EN 10163-2, class A, subclass 3.

Cold-rolled coils and sheets are delivered in an annealed state.

Hot-rolled coils and sheets are supplied in rolled or annealed condition by separate agreement.

Cold-rolled products are produced with an oiled or dry surface.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.

SSAB Boron 42 is a steel for hardening and pressing. The degree of hardness and viscosity that can be achieved after heat treatment will provide the final products with wear and impact resistance properties that guarantee a longer service life.

SSAB Boron 42 is available in thicknesses ranging from 3.00-13.00mm and widths up to 1800mm in rolls, slotted rolls and CTL. Length up to 16 meters in cut form.

The minimum bending radius of SSAB Boron 42 hot-rolled strip is 3 times the thickness of the sheet. A smaller bend radius of 1 x sheet thickness may be warranted for annealed strip products. For more information, contact SSAB Technical Support.

A test certificate according to EN 10204/2.2 (chemical composition) is part of the delivery.

A test certificate according to EN 10204/3.1 can only be provided by special agreement.

Hot Rolled Coils and Sheets: To SSAB boron thickness tolerances that exceed EN 10051 and meet 2/3 of EN 10051 as a default value.

Hot-rolled coils and sheets with shaped edges: SSAB Boron width tolerances correspond to -0/+20 mm.

Hot-rolled coils and cut-edge sheets: Width tolerances of SSAB Boron correspond to -0/+2 mm.

Hot-rolled coils and sheets: SSAB Boron is supplied with shape tolerances in accordance with EN 10051. Tighter shape tolerances are available on request.

Hot rolled sheets: SSAB Borion tolerances guarantee a maximum deviation from flatness of 6mm/m in addition to the flatness requirements of EN 10051. Flatness guarantees only apply to sheets cut to the required length.

Hot-rolled strip and hot-rolled plate: according to EN 10163-2, class A, subclass 3.

Hot-rolled coils and sheets are supplied in rolled or annealed condition by separate agreement.

Hot rolled strips are available in unetched, dry etched or etched and oiled state.

For manufacturing information, see SSAB brochures at www.ssab.com or contact technical support.

Appropriate safety precautions must be taken when bending, welding, cutting, grinding or other work with products.